Improved photoelectrochemical hydrogen production over decorated titania with copper and nickel oxides by optimizing the photoanode and reaction characteristics

We optimized photocatalytic hydrogen production over TiO₂-based photocatalyst by varying the dopant (nickel and copper oxide), thin film active area, nature and concentration of sacrificial agents, and light intensity in a photoelectrochemical (PEC) cell/dye-sensitized solar cell (DSSC). Various characterization techniques have been used to investigate the structural, morphological, optical, and PEC behavior of single and codoped TiO₂. The TiO₂ decorated with both Cu and Ni oxides with active area of 1 cm² in a mixture of 5 vol % glycerol and 1 M KOH under light intensity of 100 mWcm^?2 produced the maximum hydrogen of 338.4 μmol cm^?2 for 2 h. The superior photocatalyst performance of this photocatalyst is attributed to its small crystallite size and large pore size, as confirmed by X-ray diffractometer, Transmission electron microscopy (TEM), and surface area of Brunauer-Emmet-Teller (S_BET). The absorption edges of this photocatalyst had the highest red shift compared with single doped and pure TiO₂ because of more indirect transitions of the photoexcited electrons, greater charge carrier separation, and lower recombination rate. The photoanode active area of 1 cm² with better photocatalytic performance correlated with the number of defects and grain boundaries. Glycerol shifted the conduction band of the photocatalyst to more negative flat potential compared with others. Increasing the concentration of glycerol further than 5 vol% saturated the photocatalyst active sites, increased photooxidation intermediates of glycerol, and reduced the hydrogen production. The light intensity had the maximum impact on the hydrogen production and could strongly control the number of charge carriers in both the PEC cell and the DSSC.     

周期激励下的前包钦格呼吸神经元的簇振荡现象研究

研究周期激励作用下的非自治前包钦格呼吸神经元模型,结果表明当外界激励频率与系统固有频率存在着量级差距时,系统可以产生典型的簇放电模式.由于激励频率远小于系统的固有频率,因此将整个周期激励项视为慢变参数,从而可以利用稳定性分析理论研究慢变参数变化下的平衡点的分岔类型,进一步应用快慢动力学分析方法给出簇模式产生的动力学机理.本文的结果说明外界激励对神经元的动力学行为有着重要影响,为进一步揭示呼吸节律的产生机制提供了重要帮助.     

Emergence of a non-Fowler-Nordheim-type behavior for a general planar tunneling barrier

In this work we investigate a generalized tunneling barrier for planar emitters at zero-temperature. We present the evidence of the emergence of a non-Fowler-Nordheim-type general behavior for the field emission current density in the case that the Fermi energy (μ) is comparable with or smaller that the decay width ($d_F$). Therefore, for some non-metals or materials that have very small Fermi energy the standard Fowler-Nordheim-type theory may require a correction. In the opposite regime, i.e., for μ much larger that $d_F$, we confirm that the conventional theory is suitable for metals.     

Current-voltage characteristics of radiating Josephson sandwich

Josephson sandwich is considered, along which the radiating chain of vortices travels. Uniform movement of the chain is supported by bias current. The current-voltage characteristic connecting this current with the voltage at the Josephson junction is found. It is shown that when the current increases, generation of electromagnetic waves with frequency weakly dependent on the current is possible.     

多路Marx并联高压脉冲电源研究

脉冲功率技术在工业和生物医学领域有着广泛的应用,很多应用场合要求输出数百安培的高压脉冲。固态Marx发生器虽已研究多年,但是被广泛采用直插封装的IGBT和MOSFET功率半导体开关管的额定电流通常都低于100 A,无法满足低阻抗负载的应用需求。为提高输出脉冲电流幅值,提出两种多路Marx发生器并联的脉冲电源的拓扑结构,第一种方案采用多路Marx发生器直接并联,第二种是共用一组充电开关管的多路Marx发生器并联。由FPGA提供充放电控制信号,采用串芯磁环隔离驱动方案实现带负压偏置的同步驱动,主电路选用开通速度快、通流能力强的IGBT为主开关的半桥式固态方波Marx电路。实验结果表明,6路16级Marx直接并联的脉冲发生器能输出重频100 Hz高压方波脉冲幅值可达10 kV,在30Ω负载侧输出峰值电流可达300 A,上升时间230 ns。共用充电开关管的6路4级Marx并联发生器在5Ω电阻负载上的输出电流峰值可达300 A,最大输出电流可达460 A,上升时间272 ns。表明多路Marx发生器并联可以有效地减小系统内阻,提高系统带载能力;改进后的并联方案实现大电流脉冲输出的同时,所采用的开关管数量减小近一半,提高了系统的抗干扰能力的同时,降低了脉冲电源的成本;且增加级间并联导线可进一步改善均流效果。     

Interface trap-induced negative differential resistance in nMOSFET with floating source

Interface trap can act as the generation center in device to induce a very weak generation current. We observed the negative differential resistance NDR of this generation current I_D in nMOSFET with the floating source. It originates from that the generation function of interface trap is enabled and then is shut down in turn as increasing the drain voltage. This change relies on the interaction among the interface trap energy-level and the electron's Fermi-levels of drain and source under the floating source condition. It is found that the peak-to-valley ratio of I_D is beyond 30.     

六方相LaOF∶Er,Yb的上转换发光及温度传感特性

氟氧化物兼有氧化物优异的稳定性和氟化物的低声子能量,是上转换发光材料的一种热点基质材料,因而研究六方相LaOF∶Er,Yb的上转换发光性能及其温度特性具有重要意义。本文采用水热法制备了六方相LaOF∶Er,Yb荧光材料,通过X射线衍射(XRD)、扫描电镜(SEM)和荧光光谱对其结构和上转换荧光性能进行表征。实验结果表明,水热法120℃得到六方相LaF3,经800℃和1000℃退火后分别形成四方相LaOF和六方相LaOF。980 nm激发下,六方相LaOF∶Er,Yb中Yb3+与Er3+存在能量传递,通过双光子吸收产生绿光和红光的上转换荧光,并且Yb3+与Er3+的最佳浓度分别为3%和1%。最后研究了六方相LaOF∶Er,Yb在温度传感方面的应用,其在150~400 K温度范围的相对灵敏度和绝对灵敏度分别为0.037 K-1和0.0043 K-1。该材料具有优异的温度传感特性,对荧光温度传感器件的设计和应用具有指导意义。     

Characteristic material parameters of CIGS solar cell related with device performance

CIGS solar cells with power conversion efficiency (PCE) in the range of 1.82%–12.30% were obtained by using two-step process, and were further analyzed through various measurement techniques. Material parameters showed diverse values and some trends depending on the device performance. The lower performance device showed small integrated PL intensity, short minority life time, larger defect density and lower activation energy, whereas the higher performance device showed opposite values. We investigated relationship between material parameters and PCE of solar cells, and found that some physical parameters such as integrated PL intensity, minority life time, defect density, and difference between band gap and activation energy (E_g-E_a), which all reflect defect states in bulk and at pn interface, are strongly related with PCE and would be used as a good indicator to evaluate device performance quickly.     

The electronic properties and electron transport of sawtooth penta-graphene nanoribbon under uniaxial strain: ab-initio study

ABSTRACT

The electronic properties and electron transport of a sawtooth penta-graphene nanoribbon (SSPGNR) under uniaxial strains are theoretically studied by density-functional theory (DFT) in combination with the non-equilibrium Green's function formalism. We investigated the electronic structures and the current–voltage (I–V) characteristics of the SSPGNRs under a sequence of uniaxial strains in range from 10% compression to 10% stretch. In this strained range, carbon atoms still keep a pentagon network, but with the changing bond lengths. The C–C bond lengths change almost linearly with the tolerable strain. The value of the band gap of SSPGNRs can be depicted as a parabola under uniaxial strain. Our calculations show that the current is monotonous increase with compressive strain at the same applied bias voltage. In case of tensile strain, the variable rule of the current is different that it increases at first and decrease later. The fundamental physical properties (band structure, I–V characteristic) of SSPGNRs seem to be more sensitive to compressive strain than the stretch strain. The current intensity of the compressive-SSPGNR is by 2 orders of magnitude compared to that of the tensile-SSPGNR at the same strain in range from 6% to 10%. The results obtained from our calculations are beneficial to practical applications of these strained structures in SSPGNRs-based electromechanical devices.